-
HYUNDAI
- Apparel
- Tiburon/Tuscani 03-08
- Tiburon/Tuscani 07-08
- Elantra/Avante MD 11-13
- Elantra/Avante MD 14-16
- Elantra/Avante AD 16-20
- Elantra/Avante Sport AD 16-20
- Elantra/Avante CN7 2021 on
- Elantra/Avante N CN7 21-23
- ELANTRA/AVANTE N CN7 PE 2024 on
- Elantra/Avante N-Line 2021 on
-
Genesis Coupe 09-12
-
Genesis Coupe 13-16
- Genesis Sedan BH 09-14
- Grandeur/Azera IG 17-19
- Palisade 19-22
- Palisade Calligraphy 23 on
- Sonata NF 06-10
- Santa Fe DM/ix45 12-15
- Sonata YF 09-14
- Sonata LF 15-19
- Sonata DN8 2020 on
- Sonata DN8 N-Line
- Veloster Turbo 13-16
- Veloster NON turbo 11-16
- Veloster Turbo JS 18-22
- Veloster N 19-22
- Tucson TL 15-18
- Tucson TL 19-20
- Tucson NX4 2022+
- GENESIS
-
KIA
- EV6 2021 on
- EV6 GT-Line 2021 on
- Forte Koup 10-13
- Forte Koup/K3 Koup 14-16
- Forte Sedan 10-13
- Optima K5 TF 11-13
- Optima K5 TF 14-15
- Optima K5 JF 16-19
- Optima K5 DL3 2021 on
- Sorento MQ4 2021 on
- Sportage 04-10
- Sportage 11-15
- Sportage QL 16-18
- Sportage QL 19-20
- Sportage NQ5 21 on
- Stinger 17-21
- Stinger 22-23
- JAPAN RACING WHEELS
BBfab Splitter Kit
BBfab is proud to present its all new Genesis Coupe front splitter and side skirts package.
BBfab is proud to present its all new Genesis Coupe front splitter and side skirts package. The extended design helps to improve aerodynamic downforce by creating a low pressure area on the lower side of the splitter. Furthermore these parts add a nice amount of racing look to your car. The base material is a solid composite of a polyethylene core wrapped in two layers of aluminum. All stainless steel installation hardware plus installation guidelines including pictures are included in the kit. The splitter itself has pre-drilled holes for installation hardware. Also included in the set is a premium rubber edge protection liner in appropriate length.
The parts have a white primer finish, but painting is possible for additional cost. The kit fits both stock bumper as well as bumper with additional lip like M&S. In case of a bumper lip, the lip shouldn't be lower as the underbody plastics that are below the oil pan. In case of stock bumper, there'll be a gap between the splitter and the bumper unless you're adjusting the angle of the splitter from parallel floor level to an upward angle.
The included installation hardware is qualified for up to 180 kmh (111 mph). Higher speed can cause flutter caused by interference. Additional mounting points between the center and the outer ones will fix this. (e.g. 2 screws per side that hold the splitter to an aftermarket lip) The kit can be ordered with only front splitter or sideskirts or the whole package. Side skirts are available in standard width of 18cm.
Features:
-made in Germany
-aluminum polyethylene composite material
-predrilled splitter ready to install
-stainless steel mounting hardware included with 2 shroud tensioners (turnbuckles), two long threaded rods for the sides, bolts, nuts, washers and plastic screws
-edge protection liner included
-flat underbody design, very slim installation hardware
-detailed installation instructions included
-painting possible for additional cost
-fits 2010-2012 Genesis Coupe (-might fit 2013-2016 models, but predrilled holes would have to be made by customer)
PRICES INCLUDE SHIPPING TO EUROPE, CANADA AND USA! EMAIL US FOR SHIPPING QUOTE TO OTHER AREAS!
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent